CODE |
DESCRIPTION |
AT.EGenius.HH |
Ether.Genius hand-held tester. Battery operated. GBE tester with optional E1, data communications and synchronization capabilities includes dual 10/100/1000 Mb/s electrical ports, dual optical ports. QoS statistics, RFC2544 performance test, BER test, continuous / burst / ramp / random traffic generation, traffic statistics, error analysis, connectivity test (PING, Trace Route), analysis filters, event insertion, endpoint and through operation modes, graphical display of events, report generation and export. Includes AC/DC adapter, transportation bag, one RJ-45 patch cable, One BNC-BNC patch cable. SFP transceivers not included. |
AT.EGenius.Mstr |
Multistream Test. Generation over eight independent traffic streams. Eight analysis filters for each test port. |
AT.EGenius.1564 |
eSAM (ITU-T Y.1564). Test of up to 8 services simultaneously. Set up of CIR, EIR and policing rate. Per stream quality objectives. Measurement of Information rate (IR), Frame Transfer Delay (FTD), Frame Delay Variation (FDV), Frame Loss Ratio (FLR) and Availability.
[REQUIRES: AT.EGenius.Mstr] |
AT.EGenius.IPV6 |
IPV6 test. Decoding and analysis of IPV6 datagrams. IPV6 traffic statistics and events. IPV6 packet filtering. Top IPV6 source and destination address (with Network Search option). |
AT.EGenius.MPLS |
MPLS test. Generation of a single or double label according RFC 3032. Configuration of TTL, Traffic class, Label . Filter selection rules by Label and Traffic class field. Frame analysis of MPLS Packets. Top LSPs (with Network search option). |
AT.EGenius.WIRE |
Cable test. Wiremap with open and short circuit detection. Measurement of distance to fault. Crossover / straight cable detection. Measurement of the cable skew. |
AT.EGenius.POE |
Power over Ethernet test. PoE / PoE+ end point and pass through as per IEEE 802.3af and IEEE 802.3at with voltage and current measurement. |
AT.EGenius.NS |
Network Search. Automatic detection of up 16 most frequent streams listed by IPV4, VLAN and MAC. |
AT.VNC.RC |
Graphical Remote Control. Based on VNC for Windows and Linux. Ethernet/IP remote control that duplicates the tester graphical user interface in a remote computer. |
AT.SNMP.RC |
SNMP Remote Control and Automation. Based on SNMP protocol allows user to control the tester remotelly using SNMP queries. |
AT.20 |
Car charger. Power adapter to charge the test unit from car battery. |
AT.Lipo.Batt |
Additional Lipo battery. |
ETHER.GENIUS - E1 & DATACOM Software Options |
AT.EGenius.E1 |
E1 test. ITU-T G.703 2048 kb/s testing including BNC and RJ48 connectors, E1 generation and analysis ; internal, recovered and external clock references; G.821, G.826 and M.2100 performance analysis; frequency and received power level measurements; CAS ABCD bits generation and analysis; delay measurement. |
AT.EGenius.Data |
Datacom. DTE / DCE emulation and datacom monitor modes. V.24/V.28 (RS-232) asynchronous and synchronous interfaces, X.21/V.11, V35, V36 (RS-449), EIA-530, EIA-530A. No datacom cables included.
[REQUIRES AT.EGenius.E1] |
AT.EGenius.JW |
E1 Jitter / Wander. Peak-to-peak jitter, RMS jitter, max. jitter, jitter hits detection. Configuration of jitter filters. Frequency offset (ppm), frequency drift (ppm/s). Wander metrics (TIE, MTIE, TDEV). Sinusoidal jitter and wander generation.
[REQUIRES AT.EGenius.E1] |
AT.EGenius.Pulse |
Pulse Mask Analysis. Displays the pulse shape and checks compliance with ITU-T G.703 mask. Includes eye diagram operation mode and analysis of pulse time and level metrics.
[REQUIRES AT.EGenius.E1] |
AT.EGenius.V.24 |
V.24/V.28/RS-232 cables. V.24/V.28/RS-232 DTE and DCE interface cables. |
AT.EGenius.X.21 |
X.21/V.11 cables. X.21/V.11 DTE and DCE interface cables. |
AT.EGenius.V.35 |
V.35 cables. V.35 DTE and DCE interface cables. |
AT.EGenius.V.36 |
V.36/RS-449 cables. V.36/RS-449 DTE and DCE interface cables. |
AT.EGenius.530 |
EIA-530 / EIA-530A cables. EIA-530 / EIA-530A DTE and DCE interface cables. |
AT.80 |
VF adapter. G.711 test, PCM, level and frequency. |
AT.86 |
Stereo audio adapter. Stereo audio input adapter. |
AT.88 |
Codirectional adapter. Input / output, Smart Serial to DIN41628 (4 mm Siemens type) connector, G.703 E0 interface. |
AT.89 |
C37.94 Adapter. Input / output, Smart Serial to SFP, IEEE C37.94 interface. |
AT.90 |
RJ48 to RJ48 E1 crossover cable. |
AT.91 |
Sync adapter. Smart Serial to RJ45. External reference clock input 1 PPS. External reference clock output 1 PPS. Additional external reference clock input 2048 kbit/s, 2048 kHz, 1544 kbit/s, 1544 kHz, 10 MHz. Additional external reference clock output 2048 kHz. |
AT.HS |
Head-Set 2.5mm jack Integrated Headphone and Microphone |
ETHER.GENIUS – SyncE & PTP Software Options |
AT.EGenius.SE |
SyncE Clock Emulation. Synchronization testing according to ITU-T G.8261, G.8262, G.8264. Ethernet line frequency (MHz), offset (ppm), drift (ppm/s). Analysis / Generation of ESMC messages. External reference clock input 2048 kbit/s, 2048 kHz, 1544 kbit/s, 1544 kHz, 10 MHz, Synchronous Ethernet and 1 PPS. External reference clock output 2048 kHz and 1 PPS. 1PPS input / output adapter not included. |
AT.EGenius.SEW |
SyncE Wander test. Synchronous Ethernet TIE / MTIE / TDEV measurement. Synchronous Ethernet wander generation.
[REQUIRES: AT.EGenius.SE] |
AT.EGenius.PTP |
IEEE 1588v2 / PTP Clock Emulation. PTP master and slave emulation. PTP passive monitoring. PTP message classification and analysis. PDV analysis. External reference clock input 2048 kbit/s, 2048 kHz, 10 MHz and Synchronous Ethernet. External reference clock input 2048 kbit/s, 2048 kHz, 1544 kbit/s, 1544 kHz, 10 MHz, Synchronous Ethernet and 1 PPS. External reference clock output 2048 kHz and 1 PPS. |
AT.EGenius.PTPW |
IEEE 1588v2 / PTP wander test. PTP TIE / MTIE / TDEV measurement.
[REQUIRES: AT.EGenius.PTP] |
AT.EGenius.OCXO |
OCXO time reference. High performance internal oscillator replacing the standard time reference installed in the application board. |
AT.EGenius.GPS |
GPS receiver and antenna. Provides absolute time reference for synchronization tests through the GPS satellite network. Connection is through RJ-45 male interface. |
ETHER.GENIUS - Interfaces |
AT.Wi-Fi.RC |
Wi.Fi USB Remote Control wireless interface to be used together with VNC.
[REQUIRES: AT.VNC.RC] |
AT.1000Sx.SFP |
SFP Adapter 1.25 Gbps SFP, 850 nm, MMF, 500 m reach, w/ DDM, Duplex LC, 0 - 70ªC |
AT.1000Lx.SFP |
SFP Adapter 1.25 Gbps SFP, 1310 nm, SMF, 20 Km reach, w/ DDM, Duplex LC, 0 - 70ªC |
AT.1000Zx.SFP |
SFP Adapter 1.25 Gbps SFP, 1550 nm, SMF, 80 Km reach, w/ DDM, Duplex LC, 0 - 70ªC |
AT.Elect.SFP |
SFP Adapter 10/100/1000BT Electrical SFP transceiver, SGMII, 0 – 70ºC |
AT.100Fx.SFP |
SFP Adapter 100FX, 125 Mbps SFP, 1310 nm, MMF, 2Km reach, w/ DDM, SGMII, Duplex LC, 0 – 70ºC |
AT.C37.94Sx.SFP |
IEEE C37.94 SFP Adapter 2048 Kb/s SFP, 850 nm, MMF, Duplex LC, 0 – 70ºC |
Calibration Services |
AT.Egenius.Cert |
Certificate of calibration. Accuracy calibration certificate, executed only when is sold and before its shipment. |
AT.Egenius.Check |
Periodical Unit Verification. Includes board test verification (Calibration, Internal Frequency), test port verification (Ports A / B / C: Ethernet, SFP, unbalanced E1, balanced E1, VF Port , DTE / DCE Ports) and analog verification (level port A / B / C, line attenuation, jitter error, pulse mask). |
|
|